FEP COATED O-RINGS

These O-rings consist of a seamless and uniform FEP jacket that completely encloses a core material, in this case the elastomer silicone, silicone white, EPDM, FPM black or FPM white with FDA and USP class VI conformity. ECAP FEP encapsulated O-rings are specified by the dimensions inner diameter x cross section (ID x QS). The minimum inner diameter is 5.28 mm, with no upper limit. The cord thicknesses range from 1.60 mm to 32.00 mm (approx. 40 different diameters).

Properties

1) High resistance to chemicals due to FEP coating
2) Operating temperature range from -60 °C/-320 °F to +205 °C/400 °F
3) Non-stick properties / non-stick surface
4) Sterilizable, FDA conformity according to 21 CFR 177.1550
5) Low vapour permeability and minimal water absorption
6) Low compression set

Remarks

O-rings with FEP coating are resistant to almost all chemicals due to the coating. The FEP coating is fully integrated and has no weak points such as visible seams or overlaps.

The FEP coating of ECAP O-rings has a very low coefficient of friction. The elastomer core of ECAP-O-Rings ensures permanent contact with the sealing surfaces. ECAP O-rings combine the best qualities of FEP compounds and silicone, EPDM or FPM elastomers . For this reason, these O-rings represent a cost-effective, efficient and economical solution for many critical sealing problems.

Performance features

High resistance to chemicals. Attacks by chemicals and swelling are the main reasons for O-ring failures. ECAP O-rings are practically chemically inert and do not swell.

They outperform solid PTFE O-rings in terms of performance. Encapsulated O-rings have the same resistance to chemicals as solid PTFE O-rings. ECAP O-rings have elasticity and recovery properties that are critical in many sealing applications.

In terms of economy and effectiveness, ECAP O-rings are replacing FFKM and other exotic O-ring composites. ECAP O-rings reduce downtime and therefore increase profitability in many cases.

ECAP O-rings can withstand applications caused by industrial solvents and corrosive substances at temperatures between -60°C / -75°F and +205°C / 400°F.

Non-stick surfaces allow easy removal of viscous media.

Low coefficient of friction, self-lubricating surface

Health, contamination of fluids by elastomers is prevented. Sterilizable and FDA compliant.

No size restrictions, the rings are available in standard and metric sizes in almost any size.

Low compression set: ECAP O-rings consist of a solid silicone or fluorocarbon core that is seamlessly encapsulated in FEP (with a wall thickness of 0.010 to 0.045 depending on the cross-section). This combination meets or exceeds the requirements of L-Pl389A and ASTM-D-2166.

Recommendations for the design of the groove for ECAP O-rings (O-rings with FEP coating)
Cross sectionNominal crushMin. ID rangeMax. ID rangeGroove width
0.070 (1.78 mm)0.020 (0.51 mm)0.250 (6.35 mm)1.50 (38.10 mm)0.100 (2.54 mm)
0.103 (2.62 mm)0.025 (0.64 mm)0.500 (12.70 mm)2.50 (63.50 mm)0.130 (3.30 mm)
0.139 (3.53 mm)0.030 (0.76 mm)1.00 (25.40 mm)5.00 (127.00 mm)0.175 (4.44 mm)
0.210 (5.33 mm)0.045 (1.14 mm)2.10 (53.34 mm)Any0.275 (6.98 mm)
0.275 (7.00 mm)0.050 (1.27 mm)3.00 (76.20 mm)Any0.350 (8.89 mm)

NOTE: The above specifications refer to the recommendations for the minimum width and depth of machined grooves in metal. Recommended surface finish of 32 microinches or more.

General specification

  1. Sheathing: FEP (tetrafluoroethylene hexafluoropropylene)
  2. Core material: Elastomer silicone red, silicone white, silicone hollow core, EPDM black, EPDM white or FPM black
  3. Operating temperature: FEP: 400 °F / 204 °C
  4. Coefficient of friction: 0.1 to 0.2
  5. Wasseraufnahme: <0,01
  6. Average total Shore A hardness
    85-90 Shore A for solid silicone core
    90-95 Shore A for solid Viton core
    75-80 Shore A for hollow silicone core
    75-80 Shore A for hollow FPM core
  7. FDA Compliance: The clear FEP wrapping of the ECAP-O-Rings complies with Title 21, Section 177 of the Food and Drug Administration's regulations for safe use as an article or component of articles for producing, manufacturing, processing, preparing, handling, packaging, transporting or storing food under regulation 177.1550.